Best Ice Cleats for Work Boots

Top pick: Ergodyne TREX 6310 for all-day wear over work boots

For most people who need ice cleats over work boots on a jobsite, yard, loading dock or delivery route, buy the Ergodyne TREX 6310. It is a one-piece stretch rubber sole that hugs the toe and heel of the boot, with an adjustable cord that cinches tight and large thumb tabs at the heel. Ergodyne fits each foot with 10 heat-treated carbon steel studs and a thicker under-sole tread that connects the mid-foot and heel stud zones. Ergodyne lists a pair at $30.65 in sizes M, L and XL.

Get Ergodyne TREX 6310

Every pick on this list was judged on five points: the traction element (studs, coils or spikes) and the surface it suits; how it fits over a work boot, including insulated and safety-toe boots; whether it stays on when you kneel, crouch or climb into a cab; what happens on indoor concrete; and price. These picks were not tested. This is what the makers’ specifications, size charts and retail listings show, with owner reports marked as owner reports.

The 6310 wins on two things: staying on and upkeep. A stretch-rubber harness holds only by tension, so it can roll off the heel when the boot bends hard at the toe, and kneeling does exactly that. The 6310 adds a cord you pull tight on top of the boot once the cleat is on, and Ergodyne says the cord cinches tight for a secure fit. Ergodyne tests the rubber to stay flexible down to -40°F (-40°C). Upkeep matters because studs that hit bare concrete and asphalt between ice patches wear down. Ergodyne sells TREX 6301 replacement studs, 8 heat-treated carbon steel studs for $5.95, that pop out of the sole and back in, so a worn stud does not mean a new pair. Ergodyne also gives a separate work-boot size chart: M fits men’s 5-7.5, L fits men’s 8-10.5 and XL fits men’s 11-13.

Who should not buy it: anyone who walks in and out of buildings every few minutes. Ergodyne says the TREX 6310 is best for construction, road work and applications without much or any transitioning from vehicles or buildings, and its selection chart marks it for outdoor use only. Anyone with a work boot above a men’s 13 is past its largest size; the TREX 6300 below comes in a 2XL. Anyone working on steep, rough ice on a hillside or frozen embankment should look at the longer spikes of the next pick.

Kahtoola MICROspikes: the most bite on hard, rutted and sloped ice

Kahtoola MICROspikes put 12 spikes under each foot. Kahtoola lists each spike at 0.41 inch (10.4 mm) long, made of heat-treated 400-series stainless steel and hung on stainless chains. An elastomer harness holds them on, and a raised heel tab helps you pull them on with gloves. Kahtoola makes sizes XS through XXL and lists a pair at $89.95.

Get Kahtoola MICROspikes

That spike length is the point. Kahtoola says the spikes bite into the most stubborn ice and snow, and it builds MICROspikes for ice and packed snow in mountainous terrain. On glare ice, frozen ruts, sloped driveways and frozen ground, long spikes push into the surface instead of riding on it. This is the pick for surveyors, utility and line crews walking right-of-way, ranch and farm hands, and anyone whose winter ground is uneven ice rather than a flat lot.

Who should buy something else: workers who cross bare pavement or go indoors often. Long spikes on concrete are loud, concentrate your weight on 12 points and slip on polished floors. The harness also depends on stretch rather than straps; Kahtoola says it retains its elasticity down to -22°F (-30°C). Kahtoola says to inspect the device before each use, remove it from footwear between uses, and not to dry it with heat. A size that is loose over a slim boot can shift when you kneel. If you mostly walk a paved yard with patches of ice, the Ergodyne TREX 6310 or another stud cleat suits that ground better.

Ergodyne TREX 6300 and TREX 6317: the budget pair and the heeled-boot cleat

The Ergodyne TREX 6300 is the one to buy when you need a cheap pair, or several for a crew. Ergodyne lists it at $21.65. It is a one-piece stretch rubber sole that hugs the toe and heel, with 8 heat-treated carbon steel studs per foot, a thicker under-sole tread, a reinforced toe cap and large thumb tabs at the heels. Ergodyne’s work-boot sizes run M for men’s 5-7.5, L for men’s 8-10.5, XL for men’s 11-14 and 2XL for men’s 15-17.

Get Ergodyne TREX 6300

The missing cord is the trade-off. Ergodyne says the stretchy one-piece design needs no tightening or adjustments, so the fit rests on the rubber alone and on buying the right size. It takes the same TREX 6301 replacement studs as the 6310. Treat the 6300 as the spare pair kept in the truck, or the pair for crews who wear cleats now and then. Ergodyne marks the 6300 for outdoor use only, best for applications without much or any transitioning from vehicles or buildings. If you will kneel and crouch in cleats every shift, spend the extra $9 on the 6310 for its cord.

The Ergodyne TREX 6317 is a different tool: a mid-sole cleat for heeled boots, such as western work boots, logger boots and lineman boots. It sits under the arch in front of the heel, and Ergodyne molds tungsten carbide studs (12 per cleat in its feature list; 6 per foot in its photo caption and selection chart) into a thick rubber wedge that fills the gap under the arch. It comes in one size. When you go indoors, Ergodyne says to rotate the cleat to the top of the boot to prevent surface damage. Ergodyne says tungsten carbide rates 9 on the Mohs scale for hardness, second only to a diamond, and calls the studs extremely durable. Ergodyne lists it at $32.05.

Get Ergodyne TREX 6317

Buy the 6317 if your boot has a defined heel of 0.6 to 1 inch (16 to 25 mm), the range Ergodyne gives, and full-sole cleats sit badly over it. Ergodyne says it is not designed for flat-style footwear with little to no arches or heels. Do not buy it if you walk down icy slopes. The heel lands first going downhill, and Ergodyne lists this design’s traction coverage as mid sole.

Yaktrax Pro and Yaktrax Diamond Grip: coils and beads for sidewalks and lots

The Yaktrax Pro wraps 1.4 mm steel coils around a natural rubber outer band and adds a removable strap across the top of the foot. Yaktrax lists it at $29.99, and Yaktrax’s size chart puts men’s 9-11 in one size, with smaller and larger sizes on either side.

Get Yaktrax Pro

Yaktrax lists packed snow, pavement, mixed conditions and slush as the Pro’s surfaces. On hard, clear ice or a slope, a low coil has no point to drive into the surface the way a stud or spike does. Buy the Pro for walking routes on cleared sidewalks with snowpack, such as meter reading or mail and parcel delivery. Do not buy it as your only cleat for an icy yard or a ramp. Yaktrax limits the product’s fitness for use to a traction augmentation device on outdoor ice and packed snow.

The Yaktrax Diamond Grip swaps the coils for diamond-shaped beads of case-hardened steel alloy strung on cable. Yaktrax says the beads have biting edges that grip in all directions and pitches the Diamond Grip for everything from boilerplate ice to backcountry snow, while it still has no long spikes. Yaktrax lists it at $59.99. Yaktrax’s size chart warns that insulated boots add two shoe sizes. A men’s 8 in a pac boot therefore sizes as a 10, which moves you from the men’s 6.5-9 size up to the 9.5-12.5 size.

Get Yaktrax Diamond Grip

The Diamond Grip suits parking lots, plant yards and sidewalks where ice is patchy and spikes would be overkill. Yaktrax limits the product’s fitness for use to a traction augmentation device on outdoor ice and packed snow. If you walk through brine every day, rinse the pair with fresh water and dry it after each shift.

Studs, coils and spikes: what each traction type grips

Traction devices for boots come in three types, and the type matters more than the brand.

Ask where you spend most of your steps. If you are on flat ice in a work yard, buy studs. If you are on snow-covered sidewalks, coils or beads are enough. If you are on sloped or broken ice away from pavement, buy spikes. More money buys harder points (6317) or longer stainless spikes (MICROspikes). Replaceable studs come on the inexpensive TREX 6300 and 6310. No one device does everything.

The cheapest option is not always the best value. The Ergodyne TREX 6300 at $21.65 is the cheapest pick here, and the 6310 costs $9 more for its cinch cord. Both take TREX 6301 replacement studs at $5.95 for 8, so a pair you wear every day can be kept going instead of thrown out when a few studs wear.

Fitting cleats over work boots, insulated boots and safety-toe boots

Ice cleats are sized by shoe size, but a work boot is longer and wider than a shoe of the same size. Ergodyne’s chart for the TREX 6310 has a separate work-boot column: M fits men’s 5-7.5, L fits men’s 8-10.5 and XL fits men’s 11-13. Yaktrax’s Diamond Grip size chart says insulated boots add two shoe sizes; its Pro page recommends one size larger than your normal shoe size for oversized shoes or boots. That rule is worth using with any brand when your boot is a pac boot or a heavily insulated winter boot.

Safety-toe boots have a blunt, tall toe box, and a stretch harness has to climb over it. If you are between sizes on a composite or steel toe, take the larger size and tighten it with the cord on the TREX 6310 or the strap on the Yaktrax Pro. An undersized harness strains at the toe. Logger and lineman boots with a defined heel are what the TREX 6317 is built for.

Cleats only add grip. They do nothing about wet feet. If your boots leak at the flex point or the welt, fix that first, and the best waterproof work boots list covers the boots that pair well with these cleats.

Fit check before your first shift: put the cleat on, kneel on one knee, stand, then climb in and out of a truck cab. If the heel lifts or the device slides toward the toe, it is too big or too loose. Ergodyne says TREX cleats enhance traction on ice and packed snow but will not eliminate the inherent risk of such conditions, and to always use caution and reasonable care.

Kneeling, ladders, concrete floors and going indoors

Kneeling is hard on stretch harnesses. When you kneel, the boot bends sharply at the ball of the foot, and the rear of the harness can ride up and off the heel. A cinch cord, as on the Ergodyne TREX 6310, lets you tighten the fit before you kneel. A plain stretch harness relies on its rubber alone.

Take full-sole cleats off before climbing a ladder. Ergodyne markets the mid-sole TREX 6317 for tasks involving driving or ladders where a full cleat could cause damage or injury. Steel studs or spikes on an aluminum or fiberglass rung put a few small hard points on the rung instead of the full rubber sole of the boot, and that is less grip, not more. The same applies to steel plate, diamond-plate truck steps and smooth vehicle floors.

Indoors, metal studs and spikes slip on sealed or polished concrete, tile and epoxy floors, and spikes can gouge finished floors. Anyone who goes in and out all day should choose a cleat that comes off quickly and keep it on a hook by the door. Ergodyne says the TREX 6310 is best for applications without much or any transitioning from vehicles or buildings. None of the makers here describes these picks as spark-resistant, so in spark-sensitive areas, check your site’s safety rules before wearing any of them.

What is not worth the money: carbide studs if your shift is mostly fresh snow over soft ground, long spikes if you mostly walk paved lots, and coil devices if your problem is thick glare ice. Each of those buys toughness you will not use, or skips the traction you need.

FAQ

Can you wear ice cleats inside a building?

Not safely on hard floors. Steel studs and spikes slip on sealed concrete, tile and epoxy, and spikes can scratch finished floors. Take them off at the door. If you go in and out often, choose a cleat with a heel tab that comes off quickly.

Do ice cleats fit over steel-toe or composite-toe boots?

Yes, but a safety toe is bulkier than a shoe toe. Ergodyne gives a separate work-boot size chart for the TREX 6310, and Yaktrax’s Diamond Grip size chart says insulated boots add two shoe sizes. Between sizes, go up and tighten with the cord or strap.

Which last longer on pavement, studs or spikes?

Short studs handle bare pavement better than long spikes, and hard or replaceable studs extend a pair’s life. Ergodyne calls the tungsten carbide studs on the TREX 6317 extremely durable, and it sells TREX 6301 replacement studs for the TREX 6300 and 6310, so a worn stud does not mean a new pair. Spikes and coils wear faster when you drag them across concrete.