Best Roofing Nailers (2026): Pneumatic and Cordless Coil Picks
Which coil roofing nailer to buy, and who each one is for
Buy the Metabo HPT NV45AB2 if you shingle roofs for pay or are re-roofing a whole house. Metabo HPT lists it at 5.7 lb with a 120-nail magazine. It rates the gun to fire up to 10 nails per second, gives it tool-less depth-of-drive adjustment and backs it with a 5-year warranty. Depth control matters most on a shingle job. An overdriven head cuts into the shingle and loses holding power. An underdriven head stands proud under the next course.
Get Metabo HPT NV45AB2Buy the Bostitch BRN175A instead if you roof a few times a year, already keep 15° coils or want the lightest pneumatic gun on this list. The Bostitch manual for the BRN175A gives a weight of 5.3 lb and a 120-nail magazine. It takes 15° wire-collated nails with a 0.120 in shank, from 3/4 in to 1-3/4 in long.
Get Bostitch BRN175ABuy the DeWalt DCN45RNB if you already run DeWalt 20V MAX batteries and your roofing is repairs, a shed, a porch roof or punch-list work. On those jobs, carrying a compressor and hose up a ladder takes longer than the nailing. The DCN45RNB is the tool-only version, so it comes without a battery or charger.
Get DeWalt DCN45RNBThese picks were not tested; this is what the makers’ pages and instruction manuals show. Each pick had to pass four tests on its maker’s own figures:
- a documented nail specification (collation angle, shank diameter and length range)
- the tool weight a roofer holds on a pitched roof all day
- the warranty terms for the buyer’s kind of use
- for the cordless gun, the battery platform it needs
All three hold 120 nails, so magazine size does not separate them.
Metabo HPT NV45AB2: the pick for full shingle jobs
Metabo HPT’s page for the NV45AB2 lists these figures:
- nail range of 7/8 in to 1-3/4 in
- 16° magazine angle
- 120-nail magazine
- 70-120 psi operating pressure
- 3/8 in NPT air inlet
- 9-27/32 in long, 4-5/8 in wide and 10-3/8 in high
The features list adds a side-load magazine and rubber pads that keep the gun from sliding down the roof when it is set down.
For working roofers it beats the Bostitch on warranty and on a published firing rate. The Metabo HPT warranty is 5 years. Bostitch’s limited warranty for its pneumatic nailers runs seven years from purchase but only one year for tools used in production applications. Metabo HPT also states a firing rate of up to 10 nails per second from its cylinder-valve firing mechanism. The Bostitch manual for the BRN175A gives air use at 100 fasteners per minute rather than a top firing rate.
The drawback is the nail. Metabo HPT’s instruction manual for the NV45AB2 specifies 16° wire-collated nails with full round heads and a .120 in shank, 7/8 in to 1-3/4 in long. It also warns owners to use only genuine Metabo HPT nails, because any other nails can cause tool malfunction or nail breakdown, leading to serious injuries. Metabo HPT sells matching electro-galvanized, smooth-shank 16° roofing coils, including 1-1/4 in x .120 in (12111HPT) and 1-3/4 in x .120 in (12113HPT). The 15° coils that the other two picks take are not what this manual specifies.
Who should not buy it: anyone who needs 3/4 in nails, because the Metabo HPT NV45AB2 starts at 7/8 in. Metabo HPT also says never to let children, people unfamiliar with its operation or anyone who has not read the manual operate the nailer. It also does not suit anyone with cases of 15° coils on the shelf who does not want to stock a second angle. The Bostitch BRN175A does the same job on 15° nails.
Bostitch BRN175A: lighter, takes 15° nails and goes down to 3/4 in
Bostitch’s instruction manual for the BRN175A lists the gun at 5.3 lb, 10.24 in long, 10.63 in high and 4.33 in wide. Its fastener table gives:
- 15° coil roofing nails with a 0.120 in shank
- lengths of 3/4 in to 1-3/4 in
- 120 nails per load
- 70-120 psig operating pressure, with a warning not to exceed it
- a warning that ANSI Z87.1 eye protection must be worn by the operator and everyone in the work area, with ANSI S12.6 hearing protection
The manual says to use only Bostitch-, Porter-Cable- or DeWalt-approved fasteners. It is also the source for the figures here because Bostitch’s own roofing nailer page now redirects to Bostitch’s Construction Tools page, which lists the BRN175A only by name and model number.
Against the Metabo HPT NV45AB2, the Bostitch BRN175A wins on three published figures:
- It weighs 0.4 lb less: 5.3 lb against 5.7 lb.
- Its nail range goes down to 3/4 in, where the Metabo stops at 7/8 in.
- It takes 15° nails, the same angle the DeWalt cordless pick takes, so one box of coils can feed both.
For a homeowner who shingles a garage or patches a storm-damaged section, the warranty is also better: seven years from purchase against five, as long as the gun is not used in production work. Bostitch designed the BRN175A for professional roofing: its manual says not to let children come into contact with it and requires supervision when inexperienced operators use it.
It loses in two places. Bostitch cuts the warranty to one year for production use, and the manual gives air use instead of a firing rate. The BRN175A needs 4.13 cubic feet per minute of free air to run at 100 fasteners per minute at 80 psi. Compare that figure with the compressor’s CFM rating at 90 psi. A compressor rated below it falls behind a roofer nailing at that pace, and two guns on one compressor double the demand. Whatever the compressor, Bostitch says to disconnect the air supply before making adjustments, servicing, clearing a jam, when the tool is not in use and when moving to a different work area.
Who should not buy it: a roofer who works five days a week. For that buyer, one year of cover is the shortest warranty on this list. The Metabo HPT warranty lasts five years, and DeWalt’s lasts three.
DeWalt DCN45RNB: cordless for repairs, not for full re-roofs
DeWalt’s page for the DCN45RNB describes a brushless 20V MAX coil roofing nailer. Its 15° canister holds up to 120 wire-collated roofing nails. The page lists:
- a bump firing mode
- a tool-free depth adjustment wheel
- a tool-free stall release lever that returns the driver blade after a jam
- a tool-free nail tray that adjusts to the full range of roofing nails
DeWalt gives that range as 3/4 in to 1-3/4 in. The warranty is DeWalt’s 3-year limited warranty, with 1 year of free service and a 90-day satisfaction guarantee.
DeWalt’s instruction manual for the DCN45RN lists a weight of 6.8 lb (3.85 kg). It specifies full round head nails with a 0.12 in (3 mm) shank and a 15° coil angle, 3/4 in to 1-3/4 in long, smooth or ring shank. The manual does not say whether the 6.8 lb includes a battery. It warns that all users and bystanders must wear ANSI Z87.1 eye protection and ANSI S12.6 hearing protection, and that supervision is required when inexperienced operators use the tool. That nail angle, shank and length match the Bostitch manual, so one 15° coil size suits both specifications.
Cordless costs weight and warranty. At 6.8 lb, the DeWalt DCN45RNB is 1.1 lb heavier than the Metabo HPT NV45AB2 and 1.5 lb heavier than the Bostitch BRN175A. Its 3-year warranty is shorter than either pneumatic gun’s main term. In return, it does away with the compressor and the air hose dragged across fresh shingles, and setup for a 20-minute repair is just snapping in a pack once you are up: DeWalt warns not to carry the tool up ladders, stairs or scaffolding with the battery pack connected, and to remove the pack before adjusting depth or clearing a jammed nail. For replacing a few blown-off tabs, nailing down a lifted ridge cap or shingling a 10 ft x 12 ft shed, that is the better trade.
Who should not buy it: a crew re-roofing whole houses. Each pack drives a limited number of nails before it has to be swapped, and a gun fed by a compressor has no such limit. Carry a second 20V MAX pack for anything bigger than a repair. DeWalt’s manual says not to charge a pack below 40 °F or above 104 °F, not to store or use the tool and pack where the temperature may reach 104 °F, and not to expose the tool to rain or wet conditions. If you have no DeWalt 20V MAX batteries yet, the battery and charger are an extra purchase on top of the bare tool.
Nail fit: angle, shank, head and length
A coil roofing nailer takes nails held together by thin wires and wound into a coil. Three numbers decide whether a coil fits: collation angle, shank diameter and length. The Bostitch BRN175A and DeWalt DCN45RNB are specified for 15° coils, and the Metabo HPT NV45AB2 for 16°. All three manuals specify a 0.120 in shank. The DeWalt manual lists wrong size or angle nails as a cause of jammed nails, so match the coil box to the gun’s own spec before you buy a case.
The International Residential Code, section R905.2.5, sets the requirements for the nail itself:
- galvanized steel, stainless steel, aluminum or copper roofing nails
- at least a 12-gauge (0.105 in) shank and a 3/8 in diameter head
- long enough to go at least 3/4 in into the roof sheathing, or through it where the sheathing is thinner than 3/4 in
A 0.120 in coil nail meets the shank minimum. On 7/16 in or 1/2 in sheathing the nail has to come through the underside. That means the length must cover the shingle thickness at the nail line plus the full sheathing, with some left over. Ridge caps and roofs laid over an existing layer need lengths toward 1-3/4 in, the top of the range all three guns drive. Local code amendments and the shingle maker’s instructions can set a longer minimum.
Section R905.2.6 requires at least four fasteners per strip shingle, or more where the shingle maker’s instructions require it. At four nails, one 120-nail coil fastens 30 strip shingles. Where the shingle instructions call for six nails per shingle, the same coil fastens 20. With all three picks holding 120 nails, the coil runs out at the same point whichever gun is on the roof.
Air supply, upkeep, and what is not worth paying for
Both pneumatic picks have a 70-120 psi operating range, and both makers set 120 psi as the ceiling. Metabo HPT warns never to connect the NV45AB2 to an air source that can exceed 200 psi if a regulator fails, and never to power it with oxygen, carbon dioxide, combustible gases or any bottled gas, which can explode. The Metabo HPT NV45AB2’s air inlet is a 3/8 in NPT thread, and Metabo HPT’s tool card lists its fitting as a 1/4 in industrial plug, so the coupler on your hose has to match that plug. Metabo HPT warns never to use a non-relieving coupler: the coupling must remove all pressure from the nailer when disconnected, or the nailer can still drive a fastener. Metabo HPT says operators and others in the work area MUST wear safety glasses with side shields that conform to ANSI Z87.1, and to keep hands and body at least 8 inches from the firing head. Start the regulator near 70-80 psi and fire into a scrap shingle on a sheathing offcut. Raise the pressure until the heads sit flush, then fine-tune with the depth adjustment, disconnecting the air hose first: Metabo HPT says to disconnect it before turning the adjuster, clearing a jam, or elevating, lowering or moving the nailer. Turning a weak compressor up to 120 psi overdrives nails whenever the tank is full and underdrives them as it drains. Fix that with a compressor rated above the gun’s own air figure: 4.13 CFM at 100 fasteners per minute and 80 psi for the Bostitch, and about 4.7 CFM at 100 nails per minute and 90 psi for the Metabo HPT by its manual’s formula (.039 cubic feet per cycle x nails per minute x a 1.2 safety factor). Bostitch warns not to connect the BRN175A to air that can exceed 200 psi, as the tool may fracture or burst, never to power it with oxygen, combustible or bottled gases, and never to use it near flammable substances, gases or vapors, because it produces sparks.
AeroPro’s CN45N is a 15° pneumatic coil roofing nailer. AeroPro’s own shop search returns no CN45N, but CastleRock Tools’ AeroPro page lists it at 5.5 lb, taking 15° wire-collated coil nails with a 0.120 in shank from 3/4 in to 1-3/4 in at 70-120 psi; that page gives no warranty term. Compared with the Metabo HPT NV45AB2 or Bostitch BRN175A, you give up a maker-published warranty term.
Not worth the money:
- A cordless roofing nailer bought only to avoid owning a compressor for one full re-roof. The DeWalt DCN45RNB is 1.1-1.5 lb heavier than the pneumatic picks, has the shortest warranty term outside production use and is limited by its batteries for a whole roof.
- Any gun whose maker publishes no nail specification, because a coil that does not match the magazine angle jams.
Spend the money on the right nails instead: a case at the angle the gun’s manual names (16° for the Metabo HPT, 15° for the Bostitch and DeWalt), with a 0.120 in shank, long enough to meet R905.2.5 on the sheathing you are nailing into.
Related guides
- 21° vs 30° Framing Nailers: Match the Angle, Collation and Nails
- Best ATV/UTV Tool Boxes and Cargo Racks (2026): For Farm and Ranch Work
- Best Balaclavas and Neck Gaiters for Cold Work
- Best Bib Overalls for Construction and Cold-Weather Work (2026)
- Best Coil Siding Nailers (2026) and the 15° Coil Nails That Fit
FAQ
Can I use 15° coil roofing nails in the Metabo HPT NV45AB2?
The Metabo HPT manual for the NV45AB2 specifies 16° wire-collated nails with full round heads and a .120 in shank, 7/8 in to 1-3/4 in long. It warns owners to use genuine Metabo HPT nails, such as its 12111HPT (1-1/4 in) and 12113HPT (1-3/4 in) 16° coils. 15° coils are outside that specification. If you want to run 15° coils, the Bostitch BRN175A and DeWalt DCN45RNB manuals both specify them.
Is a cordless roofing nailer enough for a whole roof?
The DeWalt DCN45RNB drives the full 3/4 in to 1-3/4 in range from a 120-nail canister, but DeWalt calls it ideal for service repairs and small jobs. It weighs 6.8 lb per DeWalt’s manual, against 5.3 lb for the Bostitch BRN175A and 5.7 lb for the Metabo HPT NV45AB2, and each 20V MAX pack has to be swapped when it runs down. For full re-roofs, buy a pneumatic gun. Keep the DeWalt for repairs and small roofs where setting up a compressor takes longer than the nailing.
What compressor does a pneumatic roofing nailer need?
Bostitch’s manual for the BRN175A gives 4.13 cubic feet per minute of free air at 100 fasteners per minute and 80 psi. Both the Bostitch and the Metabo HPT run at 70-120 psi. Metabo HPT’s manual for the NV45AB2 sizes air as nails per minute x .039 cubic feet per cycle at 90 psi (.046 at 100 psi) x a 1.2 safety factor, about 4.7 CFM for one gun at 100 nails per minute and 90 psi. Pick a compressor whose CFM rating is above your gun’s figure for one gun, and roughly double it for two guns on the same compressor.
What length roofing nails do I need for asphalt shingles?
IRC section R905.2.5 requires the nail to go at least 3/4 in into the roof sheathing, or all the way through sheathing thinner than 3/4 in. It also requires at least a 0.105 in shank and a 3/8 in head. On 7/16 in or 1/2 in decking, the nail has to be long enough to come through the underside after passing through the shingles. Ridge caps and roofs laid over an existing layer need lengths toward 1-3/4 in.