Best Waterproof Winter Work Gloves for Wet Cold
The best glove for wet, freezing work: Showa 282-02
Wet, freezing work beats a glove in two steps: water gets in first, then the cold follows. This is shovelling slush, handling wet rebar and chain, pulling lines out of icy water, washing down equipment at 25°F, or loading snow-covered pallets. That work asks four things of a glove: a barrier water cannot get through, insulation that still holds heat once the hand sweats, grip on wet and icy steel, and a cuff that keeps slush out when you reach down.
The glove to buy is the Showa 282-02. The Showa 282-02 (sold as TEMRES 282-02) has a polyurethane coating on top of a fixed insulated acrylic liner. Showa states that the 282-02 rates 021 under EN 511, the European standard for cold-protection gloves. The last digit, 1, means water did not get through in the standard’s penetration test. Showa calls the coating breathable, and that is the difference from a PVC or rubber glove: sweat can escape, so the liner stays drier over a shift. Showa lists the grip finish as rough, which holds wet tools. The 282-02 is the extended-cuff version with a drawcord. Industrial suppliers list it at about $30 a pair.
Get Showa 282-02Who should not buy it: anyone standing still in wind well below zero. The first EN 511 digit measures convective cold, meaning cold carried in by moving air, and the 282-02 scores 0 on it. Its rating covers contact cold (level 2) and water, not wind. For dry, deep cold, the insulated work gloves page has the better picks. Showa rates its cut resistance at only level 2 on the EN 388 blade test (4221X), so it is the wrong glove for sheet metal or glass. Showa says not to use it where there are chemical, electrical, high-temperature or entanglement risks, that it is designed to protect down to -30°C for short or intermittent contact, to inspect the gloves for defects before use and not to use a pair that shows signs of wear, and to seek medical aid immediately after an allergic reaction.
How these waterproof winter gloves were picked
These picks were not tested. They come from what the makers publish and what retailer listings show, and the criteria are the four demands of wet, freezing work plus price:
- Barrier type. A coating (polyurethane on the Showa 282-02, full PVC on the Showa 460) leaves no seam for water to cross. An insert glove (Kinco, Carhartt, Youngstown) has a waterproof membrane between the shell and the liner. The shell still soaks up water and gets heavy, but the membrane keeps it off the hand.
- Insulation that works when damp. Youngstown puts a figure on it: 200g 3M Thinsulate. Showa lists fixed insulated acrylic liners on both of its picks; the 460’s material list also includes cotton. Kinco lists a polyester and polyethylene fill, and Carhartt lists a FastDry lining that wicks sweat.
- Grip on wet steel. That means a rough polyurethane or PVC finish, a grain pigskin palm, or a synthetic leather palm. A smooth dipped glove slides on wet pipe.
- Cuff length. The cuffs here run from a knit wrist up to Youngstown’s extended gauntlet and the Showa 460’s 11.8-inch and the Showa 282-02’s 13-inch lengths. A cuff that stops at the wrist lets slush in the first time you reach into a snowbank.
- Price. The picks run from about $25 to $46 a pair. Past that, a work glove mostly adds style, not more protection from water.
The first two criteria count most. A glove that lets water in or loses its warmth when damp fails at this job whatever it costs.
Showa 460: for hands that go into cold water
Buy the Showa 460 if your hands go into the water itself: commercial fishing, ice-tank and brine work, washdown with a hose, or fishing parts out of a sump. Showa builds it as a fully PVC-coated gauntlet with an acrylic inner and a cotton liner and states that it stays flexible down to -4°F (-20°C). Showa lists it at 11.8 inches long. At that length you can reach past the wrist into a slush-filled bucket before water comes over the top, which a knit-wrist glove cannot do.
Showa also states that the PVC coating resists oils and chemicals. Its chemical rating (EN ISO 374-1 Type C, JKL) was tested against n-heptane, 40% sodium hydroxide and 96% sulphuric acid. Showa says chemical resistance was assessed in the lab on palm samples and relates only to the chemical tested, and that movement, snagging, rubbing and degradation caused by chemical contact may reduce the actual use time significantly. Check Showa’s chemical-resistance data before relying on it for hydraulic fluid or diesel. Like the 282-02, it has a rough grip finish, which holds a wet line or a cold wrench better than smooth PVC.
The trade-off is sweat. PVC does not breathe, so on a long shift of heavy work the fixed liner gets damp from inside, and a liner that cannot be removed takes overnight to dry. If your hands get splashed rather than dunked, the Showa 282-02 is the better glove. If you are dunking them past the wrist all day, the 460 is the one. Showa says not to use it where there are electrical, high-temperature or entanglement risks, to inspect each pair for defects before use and not to use a worn pair, not to wash it (performance is not guaranteed after washing), and to seek medical aid at once after an allergic reaction.
Youngstown Waterproof Winter XT: for snow, slush and a gauntlet cuff
The Youngstown Waterproof Winter XT (part 11-3460-60) is no longer listed on Youngstown’s own store; retailers still sell it. It suits snow removal, plow drivers who get out to shovel, and winter site work where the wet comes from snow and slush rather than standing water. Youngstown builds it with 200g 3M Thinsulate insulation, a waterproof and windproof membrane, and a microfleece inner layer. Youngstown’s spec sheet lists a synthetic palm with heavy-duty non-slip reinforcement and an extended gauntlet cuff. Among these picks it is the warmest glove that still has a waterproof barrier, and its windproof membrane covers the weakness of the Showa 282-02’s convective-cold rating of 0.
Get Youngstown Waterproof Winter XTThe extended gauntlet cuff slips over a jacket sleeve, so snow does not get packed into the wrist when you dig out a buried hose or chain. Retail listings put it at about $43-46 a pair.
Who should buy something else: anyone whose hands go into water. An insert glove keeps the hand dry only up to the top of the membrane. Once water comes over the cuff, it sits inside the liner. The synthetic palm also soaks up water on the outside in slush and gets heavier over the day. Youngstown says its membrane gloves are not best for heavy rain but for intermittent rain and contact with wet items or snow, because the outer shell can absorb water. For immersion, the Showa 460 is the pick. For handling wet tools where you need to feel what you are doing, the Showa 282-02 has the thinner hand.
Kinco 1938KWP: leather palm, waterproof insert, hi-vis back
The Kinco 1938KWP is the pick for roadside, utility, and ranch crews who want a leather work glove that also stays dry and can be seen. Kinco describes it as a grain pigskin palm with a waterproof insert, a polyester and polyethylene insulating fill, a high-visibility orange back, and a knit wrist. Kinco sells it under its HydroFlector name. Kinco lists it at $43.99, and industrial retailers list it from about $23, so it is worth shopping around. Kinco also makes the same glove with a green back as the 1939KWP.
Get Kinco 1938KWPA leather palm is the choice when the wet work is also rough work: dragging frozen fence wire, carrying split firewood, handling chain. A polyurethane coating would wear through quickly there. The trade-off is that leather soaks up water. In heavy slush the pigskin wets out, and the glove gets heavier and colder even though the insert keeps the hand dry. Kinco says not to wash it (spot treatment only), states that this style contains PFAS, and gives a California Proposition 65 warning that it can expose you to lead and phthalates, including DEHP or DINP, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
Who should not buy it: anyone working in deep snow. A knit wrist lets snow in at the cuff. Pick the Youngstown Waterproof Winter XT for that, or the Carhartt gauntlet below if you want a Carhartt fit.
The Carhartt options: Storm Defender gauntlet and the A511
The Carhartt Storm Defender Insulated Gauntlet Glove (style GL0831M) is for someone who wants a gauntlet cuff and Carhartt’s sizing. Storm Defender is Carhartt’s name for its waterproof, breathable membrane, and this version has an insulated hand and a gauntlet cuff that goes over a jacket sleeve. Carhartt and its retailers list it at about $40-45. It does the same snow-and-slush job as the Youngstown Waterproof Winter XT. The difference is that Youngstown states its insulation (200g Thinsulate) and Carhartt does not state a weight for this glove. That makes the Youngstown the clearer warmth choice at the same price.
Get Carhartt Storm Defender Insulated Gauntlet GloveThe Carhartt A511 Waterproof Insulated Glove is the budget insert glove for occasional wet days, such as scraping and shovelling before a dry shift. Carhartt lists a polytex shell, a waterproof insert, a FastDry lining meant to wick sweat, a digital-grip palm with stick-grip fingers and thumb, and a fleece cuff with an adjustable wrist strap. Carhartt sells it for about $33-35. Carhartt’s glove size chart puts a men’s Large at 9-9.5 inches and an X-Large at 10-10.5 inches, measured as hand circumference. Measure your hand before ordering, because a tight insert glove squeezes the insulation and makes it less warm.
Get Carhartt A511 Waterproof Insulated GloveWho should skip the A511: anyone in wet, freezing conditions every day. Its fabric shell soaks up water faster than coated or leather gloves. Its wrist strap closes the cuff, but a strap is no substitute for a gauntlet when you reach into snow.
Drying, liners, and what is not worth the money
Showa lists fixed liners on the 282-02 and 460, and none of the other makers lists a removable liner; that decides how you run them over a week. A fixed acrylic or polyester liner that got soaked by sweat or water over the cuff can take a full night to dry. The fix is two pairs on rotation: wear one while the other dries. For the Showa 282-02 at about $30, a second pair costs less than one premium leather glove.
Dry them cuff-down on a boot and glove dryer, or hang them up at room temperature. Keep them off a radiator or a truck defroster vent. High heat stiffens PVC and cracks leather, and the Showa 460’s PVC is only rated as flexible down to -4°F to begin with. Rinse salt and de-icer off a coated glove with plain water at the end of the day. Salt left in a coating dries to a crust that wears the grip.
What is not worth the money: a leather glove sold as water-resistant with no insert, membrane, or full coating. In slush it wets through in minutes, whatever it costs. The same goes for a smooth-finish rubber glove with a cotton liner, which loses grip on wet steel and loses warmth once the cotton is damp. If rain and spray are reaching your sleeves and body too, gloves alone will not keep you dry; the rain gear for construction page covers jackets and bibs with cuffs that seal over a gauntlet.
Related guides
- 21° vs 30° Framing Nailers: Match the Angle, Collation and Nails
- Best ATV/UTV Tool Boxes and Cargo Racks (2026): For Farm and Ranch Work
- Best Balaclavas and Neck Gaiters for Cold Work
- Best Bib Overalls for Construction and Cold-Weather Work (2026)
FAQ
What does the EN 511 rating on a winter work glove mean?
EN 511 is the European standard for cold-protection gloves, and it is written as three digits. The first measures convective cold (cold carried by moving air, 0-4), the second contact cold (0-4), and the third water penetration (0 or 1). A final 1 means water did not get through in the standard’s penetration test. Showa rates the 282-02 at 021: no convective-cold rating, contact cold level 2, and a pass on the water-penetration test.
Is a fully coated glove or a glove with a waterproof insert better for wet cold?
A fully coated glove such as the Showa 460 has no fabric or leather outside to soak up water, so it does not get heavy in slush and has no cuff seam for water to cross. An insert glove such as the Kinco 1938KWP or Youngstown Waterproof Winter XT keeps the hand dry, but its shell gets wet and heavier as the day goes on. Insert gloves usually carry more insulation and handle rough work better, so pick by whether your day is mostly water or mostly abrasion.
Do any of these waterproof work gloves have removable liners?
Not on the Showa picks: Showa lists fixed insulated acrylic liners on the 282-02 and 460, so a liner soaked by sweat or by water over the cuff dries inside the glove. Youngstown, Kinco and Carhartt do not say whether their liners come out. Rotating two pairs is the practical answer. A gauntlet cuff, as on the Showa 460 or the Carhartt Storm Defender Insulated Gauntlet Glove, keeps water from getting in over the top in the first place.